Injector fitting instructions.
Recent Topics
A4 2_5 TDI 2002
KEITH DA COSTA
10/12/09 at 09:16
Escort 1-8 TDI 2000
KEITH DA COSTA
07/12/09 at 09:21
Freelander II
KEITH DA COSTA
11/11/09 at 15:53
Nissan Primera 2_2dCi (2184cc) 2002
KEITH DA COSTA
11/11/09 at 09:59
Hyundai Tucson 2_0 CRDI 2004
KEITH DA COSTA
06/11/09 at 09:14
THURSDAY, 22 OCTOBER 2009
Peugeot, Citroen, Suzuki HDI engines
Vehicle: HDI
Injector No. 0445 110 076 / 062 / 008 / 004
Cleanliness is most important.
•Once you have removed the old injectors please insure that the injector recesses are clean and that all injector heat shields have been removed from the cylinder head. If necessary obtain a seat cutter to clean up the injector seats.
•Remove the new injectors from the packing, leave the inlet plastic protective plugs on, remove the nozzle protective cap and using a small amount of the Mercedes-Benz special grease provided, “paste” the copper washer, if applicable onto the injector nozzle / cap nut, so that it does not fall off when you insert the injector into the injector recess.
•Smear the injector body with a Mercedes-Benz special grease and place the injector into the recess, fit the injector clamp and tighten to a torque of 30 Nm.
•PLEASE DO NOT USE COPPER SLIP GREASE
•Continue with the remaining injectors.
•Connect the injector leak off pipes or bar.
•Remove the inlet plastic protective plugs and fit the cleaned and blown out injector pipes.
•Tighten injector pipes and start vehicle.
•Once engine fires, do not over rev, but rather let engine tick over for a while.
•Check for leaks. N.B. see warning.
WARNING!
Due to the very high pressure of fuel within the injector pipes do not open / crack any of the fuel / injector pipes whilst the engine is running as the fine spray from a leaking pipe can cut harm you.
Posted by KEITH DA COSTA at 12:14 | POST A COMMENT
THURSDAY, 22 OCTOBER 2009
Chrysler 2.5 CRD
Vehicle:Chrysler 2.5 CRD
Injector No. 0445 110 059
Cleanliness is most important.
•Once you have removed the old injectors please insure that the injector recesses are clean and that all injector heat shields have been removed from the cylinder head. If necessary obtain a seat cutter to clean up the injector seats.
•Remove the new injectors from the packing, leave the inlet plastic protective plugs on, remove the nozzle protective cap and using a small amount of the Mercedes-Benz special grease provided, “paste” the copper washer, if applicable onto the injector nozzle / cap nut, so that it does not fall off when you insert the injector into the injector recess.
•Smear the injector body with a Mercedes-Benz special grease and place the injector into the recess, fit the injector clamp and tighten to a torque of 32 Nm.
•PLEASE DO NOT USE COPPER SLIP GREASE
•Continue with the remaining injectors.
•Connect the injector leak off pipes or bar.
•Remove the inlet plastic protective plugs and fit the cleaned and blown out injector pipes.
•Tighten injector pipes and start vehicle.
•Once engine fires, do not over rev, but rather let engine tick over for a while.
•Check for leaks. N.B. see warning.
WARNING!
Due to the very high pressure of fuel within the injector pipes do not open / crack any of the fuel / injector pipes whilst the engine is running as the fine spray from a leaking pipe can harm you.
Posted by KEITH DA COSTA at 12:08 | POST A COMMENT
THURSDAY, 22 OCTOBER 2009
BMW, Rover, Freelander Bosch common rail injectors
Vehicle:BMW
Injector No. 0445 110 047 / 048 /266 / 029 / 030 /131
Cleanliness is most important.
•Once you have removed the old injectors please insure that the injector recesses are clean and that all injector heat shields have been removed from the cylinder head. If necessary obtain a seat cutter to clean up the injector seats.
•Remove the new injectors from the packing, leave the inlet plastic protective plugs on, remove the nozzle protective cap and using a small amount of the Mercedes-Benz special grease provided, “paste” the copper washer, if applicable onto the injector nozzle / cap nut, so that it does not fall off when you insert the injector into the injector recess.
•Smear the injector body with a Mercedes-Benz special grease and place the injector into the recess, fit the injector clamp and tighten to a torque of 10 Nm.
•PLEASE DO NOT USE COPPER SLIP GREASE
•Continue with the remaining injectors.
•Connect the injector leak off pipes or bar.
•Remove the inlet plastic protective plugs and fit the cleaned and blown out injector pipes.
•Tighten injector pipes and start vehicle.
•Once engine fires, do not over rev, but rather let engine tick over for a while.
•Check for leaks. N.B. see warning.
WARNING!
Due to the very high pressure of fuel within the injector pipes do not open / crack any of the fuel / injector pipes whilst the engine is running as the fine spray from a leaking pipe can harm you.
Posted by KEITH DA COSTA at 09:02 | POST A COMMENT
THURSDAY, 22 OCTOBER 2009
Land Rover 300 TDI
Vehicle: Land Rover 300TDI.
Injector No. KBAL90P37
Cleanliness is most important.
•Once you have removed the old injectors please insure that the injector recesses are clean and that all injector heat shields have been removed from the cylinder head.
•Remove the new injectors from the packing, leave the inlet plastic protective plugs on, remove the nozzle protective cap and using a small amount of the white grease provided, “paste” the copper washer onto the injector nozzle / cap nut, so that it does not fall off when you insert the injector into the injector recess.
•Smear the injector body with a little white grease and place the injector into the recess, fit the injector clamp and tighten to a torque of 25 nm.
•Continue with the remaining injectors.
•Connect the injector leak off pipes or bar using the copper washers provided, be very careful not to over tighten the leak off bolts as they break easily.
•Remove the inlet plastic protective plugs and fit the cleaned and blown out injector pipes.
•Tighten injector pipes and start vehicle, if the vehicle has difficulty in starting loosen a few of the pipes on the injector side, crank engine to bleed the pipes. Once fuel is injecting out of the pipes, tighten and try starting.
•Once engine fires, do not over rev, but rather let engine tick over for a while.
•Check for leaks
•Place the plastic protective caps on your old injectors, clean, fill in the CORE RETURN
Posted by KEITH DA COSTA at 08:47 | POST A COMMENT
THURSDAY, 22 OCTOBER 2009
Land Rover 200 TDI
Vehicle: Land Rover 200TDI.
Injector No. KBEL98P52
Cleanliness is most important.
•Once you have removed the old injectors please insure that the injector recesses are clean and that all injector heat shields have been removed from the cylinder head.
•Remove the new injectors from the packing, leave the inlet plastic protective plugs on, remove the nozzle protective cap and using a small amount of the white grease provided, “paste” the copper washer onto the injector nozzle / cap nut, so that it does not fall off when you insert the injector into the injector recess.
•Smear the injector body with a little white grease and place the injector into the recess, fit the injector clamp and tighten to a torque of 20 - 25 nm.
•Continue with the remaining injectors.
•Connect the injector leak off pipes or bar using the copper washers provided, be very careful not to over tighten the leak off bolts as they break easily.
•Remove the inlet plastic protective plugs and fit the cleaned and blown out injector pipes.
•Tighten injector pipes and start vehicle, if the vehicle has difficulty in starting loosen a few of the pipes on the injector side, crank engine to bleed the pipes. Once fuel is injecting out of the pipes, tighten and try starting.
•Once engine fires, do not over rev, but rather let engine tick over for a while.
•Check for leaks
Posted by KEITH DA COSTA at 08:44 | POST A COMMENT